Piping Materials : Socket Weld Fittings

ASME Standard B16.11 provides dimensions and requirements for Socket weld Fittings of sizes 1/8″ and upto 4″. But in most piping material specifications for process plants, only 1/2″ to 11/2″ size socket weld fittings are used. These fittings are made with forging process. Socket weld fittings are available in ratings 300#, 600# and 900#. Reducing fittings have the same center-to-end, center-to-bottom of socket, band diameter, and outside diameters as the uniform size fitting corresponding to the largest size end connection of the reducing fitting.

Tags : #Piping_Engineering #Piping_Fittings #Socket_Weld_Fittings.

Socket Weld Piping Fittings
Socket Weld Piping Fittings

Dimensional Standards

  1. ASME B16.11 : Forged fittings, Socket welding and threaded.
  2. MSS-SP-79 : Socket Welding Reducing Insert
  3. MSS-SP-83 : Steel Pipe Unions, Socket welding and threaded.
  4. MSS-SP-95 : Swaged Nipples and Bull Plug.

Available Fittings

90 Degree Socket Weld Elbow
Used for 90 degree turn of small bore piping. Available for size range 1/8″ to 4″ as per ASME B16.11.

Dimensions Table

Used for 45 degree change in direction of small bore piping. Available for size range 1/8″ to 4″ as per ASME B16.11.

Dimensions Table

Socket Weld Caps
Available for size range 1/8″ to 4″ as per ASME B16.11. They are used for closing dead end of plain end small bore pipe.

Dimensions Table

Socket Weld Straight and Reducing Tee
Used as 90 dgree branch connections. Available for size range 1/8″ to 4″ as per ASME B16.11. They are straight as well as reducing.

Dimensions Table

Socket Weld Straight and Reducing Cross
Available for size range 1/8″ to 4″ as per ASME B16.11. They are used sparingly, as it is better to use 2 Tees for procurement point of view.

Dimensions Table

Socket Weld Full Coupling
Available for size range 1/8″ to 4″ as per ASME B16.11. These are used to connect two small bore plane end pipes.

Dimensions Table

Socket Weld Half Coupling
Available for size range 1/8″ to 4″ as per ASME B16.11. They are used as small bore branch on big bore lines.

Dimensions Table

Socket Weld Reducing Coupling
Available for size range 1/8″ to 4″ as per ASME B16.11. These are used to connect pipes of different dimeters. They basically function as reducers.

Dimensions Table

Socket Weld Union
SW Union should be screwed tight before the ends are welded, to minimize warping of seat. Inside Union, ground faced joints are preferred, although other facings are available. As per Dimensional Standard : MSS-SP-83, available sizes are 1/8″ to 3″.
Socket Weld Reducing Insert
Reducing insert is used for connecting a small pipe to a larger fitting. They are available for size range 3/8″ x 1/4″ to 1 1/2″ x 1 1/4″ as per MSS-SP-79. Available ratings are 3000 and 6000 (3M or 6M).

Materials of Construction

These fittings are forged fittings. So Materials of Construction are as follows.

  1.  A105  : Standard Specification for Carbon Steel Forgings for Piping Applications.
  2. A181 : Standard Specification for Carbon Steel Forgings, for General-Purpose Piping.
  3. A182 : Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service.
  4. A350 : Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components.

Advantages of Socket Weld Fittings

  1. They are easier to use on small-size pipelines and ends of the pipes need not be bevelled since the pipe end slips into the socket of the joint.
  2. With socket welded fittings, there is no danger of the weld protrusion into the pipeline and restricting flow or creating turbulence.
  3. No tack welding is necessary for alignment since joint and the pipe are self-aligning.
  4. It can be used in place of threaded fittings, therefore, reducing the likelihood of leaks, which usually accompany the use of threaded fittings.
  5. It is less expensive and easier to construct than other welded systems. Joints will not leak when properly made.

Disadvantages of Socket Weld Fittings

  1. With socket weld fittings, there is a possibility of a mismatch inside the fitting where improperly aligned or mated parts may create a recess where corrosion could start.
  2. The 1/16 inch recess in joint for thermal expansion pockets liquid and also can cause corrosion, is case of highly corrosive liquids.
  3. Not used in Hydrogen Service. (All fittings are Buttwelding including small bore for hydrogen service).
  4. Use not permitted by ANSI B31.1 if severe vibration or crevice corrosion is anticipated.

Applications of Socket Weld Fittings

  1. For lines conveying flammable, toxic or expensive material, where no leakage can be permitted.
  2. For steam: 300 to 600 PSI, and sometimes 150 PSI steam.

Fittings Classes

Ratings for Socket Welded Fittings are Class 3000, 6000 and 9000.
Choice of Class depends on thickness schedule of pipe, as given in ASME B16.11. Socket welded : 3000:Sch 80 and XS, 6000: Sch 160, 9000:XXS

Sample Piping Material Specification

Elements : 45 Degree elbow, 90 Degree elbow, Equal Tee, Reducing Tee, Caps, Full Coupling, Reducing Coupling

  1. Carbon Steel  : ASTM A105. Galvanised, NIC, HIC as per spec.
  2.  Stainless Steel : ASTM A182 F304L
  3. Class SW : 3000:Sch 80 and XS, 6000: Sch 160, 9000:XXS
  4. Ends : Socket Weld Ends, Threaded Female Ends, Dim Standard : ASME B16.11

Elements : Concentric Swage, Eccentric Swage

  1. Material : CS : Made from seamless pipe ASTM A234 Gr. WPB
  2. Material : SS : Made from seamless pipe ASTM A403 Gr.  WP304LS
  3. Ends : Both Ends Plain, Bevelled larger end-Plain Small End (if large size 2” and above).

Elements : Reducer Insert

  1.  Material : CS : ASTM A105,
  2. Class : 3000,
  3. Ends : Socket Weld Ends,
  4. Dim Standard : MSS-SP-79